FurEx Step 1 - 3, loosens collected undercoat

Fur-Ex is an advanced 3-point system specifically formulated to assist in the removal of collected undercoat of double-coated breeds after the bath.

Used as directed, this system eliminates the need to pre-groom heavy undercoated dogs before the bath. Let our products do the job and use a forced air dryer to do the hard work.

For your confidence as a professional, this shampoo does not contain soaps, harsh detergents, SLS or SLES, Parabens or Petrochemicals.

STEP 1 Prepares coat for loose hair removal and begins deshedding process.

STEP 2 Innovative formula to facilitate the removal of excess fur.

STEP 3 Promotes maximum release of tangled and collected hair. FurEx Close Finishing Spray Step 3 is a mildly acidic, leave-in conditioning formula that will further seal the hair cuticle and promote maximum release of tangled and collected hair within the coat.

The unique FurEx system has been scientifically designed to work together to greatly reduce the time and effort of removing collected undercoats.

For best results, always use all three of the FurEx system products.

Benefits:

• Straight into the bath
• No Pre-brushing
• Kinder and Easier on both groomer and pet
• All the grooming is done in the bath
• No major clean up
• Saves grooming time
• Long lasting fragrance
• Safe to use on cats

Suitable for:

• All double coats
• Short and long coats
• Heavy coats
• Any dog breed that drops hair
• Cats
• Ideal for Labradors, Pugs, German Shepherds, Samoyeds, Border Collies

How to use – Step 1 - 3

For best results, always use all three of the FurEx system products

It is important to follow the Instructions

For Best results, please watch our video prior

Shake the bottle thoroughly before use

FurEX is concentrated should be diluted before usage

Tip; add water volume first, then add the product and shake well

Step 1

1. Dilute 1 part shampoo to 10 parts water (or add 30- 60 mls to hydrobath holding tank)
   requires 2 washes (first wash only can be used in the hydrobath)
2. 2nd wash must be hand washed. Dilute 1 part shampoo to 4 parts water

Step 2 must be applied by hand

1. Dilute 1 part shampoo to 3 parts water
2. Apply Diluted FurEx Release Conditioner Step 2
   
3. Work product deep into the coat
4. Brush or comb conditioner well into the coat (in this step you release excess loose hair)
5. Rinse well
6. Towel dry

The more emphasis on application and technique in step 2 will save you a lot of extra time drying and after bath brushing.

After shampooing & conditioning with FurEx Steps 1 and 2: Towel dry well or blow off excess water with force dryer

Step 3 Close Finishing Spray. Do NOT dilute

1. Spray damp coat thoroughly with Step 3 Close Spray lifting coat up from roots and spray well underneath to ensure the entire coat is covered
2. A light but thorough coverage is required
3. Use a high velocity forced air dryer to gently blow out the loosened coat
4. Spray more product if necessary, on more difficult areas
5. Dry coat thoroughly
6. Run brush and comb to remove any remaining loose hair

Always use diluted shampoo within 24–48 hours

See the downloadable Fur EX Dilution Chart to assist in approximate volumes

For best results, always use all three of the FurEx system products.

This unique product also contains a long-lasting deodorizing agent. Adjust the amount of spray applied to different areas of the coat as needed.

Safety considerations:

• Always read and follow the instructions carefully, including any warnings for use
• It is important to avoid contact with the eyes
• If a dog is squinting or rubbing at eyes, flush gently with tepid water for 5 minutes
• Always use diluted product within 24–48 hours